Niko VR6
Membres
- Inscrit
- 25/2/21
- messages
- 163
- Localisation
- Metz, Grand Est,France
- Marque
- VW
- Modèle
- Touran
- Date
- 23/9/03
- Cylindrée
- 2
- Km
- 280000
- Type
- Diesel
- Code moteur
- AZV
- VIN
- WVGZZZ1TZ4W048222
- VCDS
- VCDS
J'ai essayé de mettre 0, test, sauver et ensuite de mettre 1 test, sauver, appuyer sur déverrouillage les clignotant fonctionne une fois mais rien ne fonctionne.
Ou alors je m'y prend mal
Je m'y connais plus avec Odis que VCDS mais avec Odis il faut des codes (que j'ai pas) pour activer une clé.
Non non le code dans Odis, c'est bien ton identifiant ainsi que ton mot de passe personnel et vue que je n'ai plus ces codes je peux malheureusement pas « activer » ma clé.
Je ne sais pas le faire avec le VCDS et j'ai peur de faire un peu n'importe quoi et de ne plus pouvoir démarrer la voiture après.
Special Notes
If the remotes will not operate but are confirming while matching during the Adaptation process check the following possible causes:
- Verify the module is not new and still in Factory Mode.
- Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.
- Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Centeral Electronics and 16-Steering Wheel.
'If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:
- Incorrect remote(s)
- Incorrect Coding
- Factory Mode enabled in new module
- Incorrect control module
- Old remote control positions aren't cleared. Use the
Les liens ne sont visibles que pour les membres confirmés.procedure as needed.
Remote Control Synchronization
- If locked, open the car using the drivers door lock.
- Press the remote control unlock button.
- Put the key in the ignition lock and switch on ignition.
- Switch off ignition and pull the key out of the ignition lock.
- Press the remote control lock or unlock button.
The synchronization is now finished.
Donc je mets bien 0 dans le canal 000 du boitier confort et sauvé ? Ensuite je fais l’apprentissage de la clé comme indiquer
Adresse 46: Module confort Labels: 1K0-959-433-MIN.clb
No. pièce: 1K0 959 433 C
Pièce: KSG 0201
Codage: 18E800487F2D8504084F0100 <- CODAGE DU MODULE CONFORT AVANT CHANGEMENT
No. Atelier: WSC 68039 141 99289
VCID: 306F411CA336CEA1DFB-8065
Aucun code défaut trouvé.
Si tes clefs enclenchent quelque chose quand tu appuies sur la télécommande, c'est qu'elles sont reconnues, mais avant de tenter autre chose, il te faut faire un reset clés comme indiqué par l'ami @BigBob, et ensuite voir si tu peux actualiser tes clés dans le module confort.
Je connais certains clients qui après avoir prêté les clés de la voiture aux enfants, ces derniers avaient frénétiquement appuyé sur les touches close/open et en fait la voiture qui n'était pas a portée, ne reconnaissait plus les codes, un reset avait régularisé le problème, plus de 100 codes de différence entre la voiture et la clé, et ton module ne reconnaît plus !!!
Special Notes
If the remotes will not operate but are confirming while matching during the Adaptation process check the following possible causes:
- Verify the module is not new and still in Factory Mode.
- Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.
- Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Centeral Electronics and 16-Steering Wheel.
'If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:
- Incorrect remote(s)
- Incorrect Coding
- Factory Mode enabled in new module
- Incorrect control module
- Old remote control positions aren't cleared. Use the
Les liens ne sont visibles que pour les membres confirmés.procedure as needed.
Ce qui me rend septique c'est pourquoi ça n'a jamais fonctionné avant
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?